|
Internal Doorseal
M7/M7B |
|
Features |
|
- Tough PVCu carrier in white or
brown
- Silicone rubber compression
seal
- Integral flexible secondary
seal (M7B only)
- Low closing force required
- Easy to fit
|
 |
|
Performance Benefits |
- Easily compressed for ease of
door operation
- Excellent memory and wear
resistance
- Completely resistant to
weathering
- Supplied with stainless steel
fixing pins
|
|
Typical
Applications |
- All exterior door perimeter seals
- All interior door perimeter seals
- Casement windows with large gaps
|
|
Product
Specification |
- The product is supplied in cut
lengths of 2.1m (6'-10⅝"), in bundles of 50 pieces, with fixing
pins packed with the product. Doorsets, consisting of 2x2.1m
length and 1x1.05m length are also available to special order.
- Holes for fixing pins are
provided spaced at 125mm (5") centres, and are aligned along the
groove for ease of additional hole drilling.
- M7 has angled style carrier.
- M7B has box style carrier.
|
|
Part No. |
Carrier |
|
Style |
Colour |
| 61136 |
M7 |
White |
|
61137 |
M7 |
Brown |
|
61138 |
M7B |
White |
|
61139 |
M7B |
Brown |
|
| |
|
Technical Details |
- The seal is made from high
quality silicone rubber with outstanding properties of
compression set and weathering. It will resist the elements
between -20°C to 200°C without shrinking, cracking or perishing.
It has excellent resistance to ageing, UV and Ozone. As the seal
is compressed it also seals between the carrier and the frame.
- The carrier is extruded from
impact resistant UPVC. Smooth design lines and a linear groove
give it an appealing, easy clean finish. On angled carriers, the
rear edge is designed to seal to the frame when the pins are
driven home. On the box carriers a secondary flexible seal is
provided. Extra pins can be driven straight through the carrier
where required.
|
|
Fitting Details |
|
The seal fits on the outside of the
door frame, to the head and both sides. Measure and then cut to
length the piece to fit the head of the frame to give a neat butt
corner for box carrier, notched for angled. Offer up to the door
ensuring approximately 25% compression is present along the entire
length the seal before the pins are driven home into the frame.
Measure then cut to length the two
upright pieces and fit to the door frame in the same manner as
above. The carrier should be double pinned at the bottom of the
door frame. |
|
|
|
Standards |
|
Compliance
with BS 7386:1990 Class II Product |
|
Parameter |
|
Standard Requirement |
Test Result |
|
A2. Product size and dynamic
characteristics (N) Maximum |
|
60 |
42.8 |
|
A3. Set under sustained
compression (% recovery) Minimum |
-10°C |
55 |
98 |
|
20°C |
55 |
76 |
|
55°C |
55 |
80 |
|
A4. Sliding frictional force
(N/m) Maximum |
L |
20 |
5.6 |
|
T |
20 |
5.0 |
|
A5. Integrity of working
section (N) Minimum |
H |
20 |
35.1 |
|
V |
100 |
114.5 |
|
A7. Air leakage m³/h @ 100Pa
Maximum |
|
7.45 |
0.50 |
|
A8. Resistance to wear (mm)
Maximum |
|
0.50 |
0.38 |
|
|
back to top |
|
technical
specifications page |
|
| |
|
