|
Silicone Totalseal |
|
Features |
|
- Silicone rubber compression
seal
- Maintenance free
- Unaffected by over-painting
- Low closing force required
- Easy to fit
|
 |
|
Performance Benefits |
- Easily compressed for ease of door or window
operation
- Excellent memory and wear resistance
- Completely resistant to weathering
- Accommodates varying gap sizes
|
|
Typical
Applications |
- Metal casement windows
- Timber casement windows
- Metal/Timber pivot windows
- All rebate fitted perimeter
door seals
|
|
Product
Specification |
- The product is supplied in
packs of 100m (2x50m cut lengths) in clear polythene. Other
lengths to special order. Colours available are white and brown.
Two 310ml cartridges of silicone adhesive of the appropriate
colour are supplied with each 100m pack of totalseal.
|
|
Part No. |
Size |
Colour |
| 61008 |
Ø4.4 |
White |
| 61001 |
Ø4.4 |
Brown |
| 61002 |
Ø5.5 |
White |
| 61003 |
Ø5.5 |
Brown |
| 61004 |
Ø7.5 |
White |
| 61005 |
Ø7.5 |
Brown |
| 61006 |
Ø10.7 |
White |
| 61007 |
Ø10.7 |
Brown |
|
| |
|
Technical Details |
|
Sealcraft Totalseal is made from
high quality silicone rubber which has outstanding properties of
compression set and weathering. It will resist the elements
between -20°C to 200°C without shrinking, cracking or perishing.
It has excellent resistance to ageing, UV and ozone. |
|
Fitting Details |
|
The seal fits in the rebate of the
window or door frame. The tube should be fixed so that it is 1-2mm
inside the edge of the rebate on three faces, and on the hinge
side just out from the corner on the side of the rebate.
The tube must be fitted in the
rebate as a separate piece for each side with corners butted to
form a 'T' joint. It must not be bent round corners. It is
essential that the tube is continuous in its seal. Where sizes
change, the joint must be sleeved with the next available size.
A bead of adhesive 1.5mm to 2.5mm
wide, should be applied in a continuous pass down one face only.
The tube is laid into the adhesive using the moulded lines as a
guide, pressed onto the adhesive and cut to length. Repeat for
remaining pieces.
The window or door should be
secured partially open for approximately 30 minutes. Full cure of
adhesive takes approximately 48 hours. |
|
|
|
Standards |
|
Compliance
with BS 7386:1990 Class II Product |
|
Parameter |
Standard Requirement |
Test Result |
|
4.4 |
5.5 |
7.5 |
10.7 |
|
A2. Product size and dynamic
characteristics (N) Maximum |
|
80 |
15 |
33 |
49 |
38 |
|
A3. Set under sustained
compression (% recovery) Minimum |
-10°C |
55 |
76 |
82 |
73 |
78 |
|
20°C |
55 |
89 |
86 |
92 |
86 |
|
55°C |
55 |
78 |
72 |
74 |
81 |
|
A7. Air leakage m³/h @ 100Pa
Maximum |
|
7.45 |
0.25 |
0.3 |
1.3 |
1.7 |
|
A8. Resistance to wear (mm)
Maximum |
|
0.50 |
0.46 |
0.43 |
0.28 |
0.35 |
|
|
back to top |
|
technical
specifications page |
|
| |
|
